Ready Fit Motorbike Covers

Scooter Cover Medium | Outdoor Use

Scooter Cover Medium | Outdoor Use

Additional Information

Part # SCOOTER-SIZE4
Brand Coverworld Range
* Designed for Outdoor Use
* Reinforced security grommets are on each side panel which can be used with optional cable and lock kit.
* Sizes available for most popular Scooters
* Grey Colour Solution dyed polyester with Urethane Inner Coating
* 1 Year Warranty
Material No
Shipping Normally Dispatched 1-2 Days

* Required Fields

$92.00
Scooter Cover Medium | Outdoor Use

Mouse over to zoom image

Details

Cover Length 170cm to 193cm

We recommend you check your bike dimensions before ordering

This Scooter Cover can be used with the following Motorbike Style

  • MEDIUM SCOOTERS
  • Up to 1700mm to 2000mm / 67" to 79"
  • For models with Windshield, Sissy Bar or Rear Box and Saddle Bags
  • Colour = Grey
  • 1 Year Warranty




  • Scooter Cover Material is a Silver-coloured urethane coated polyester fabric reflects heat, is waterproof and lightweight.
  • Side panels are light weight PVC coated nylon to assist smaller storage and easier handling
  • Reinforced security grommets are on each side panel which can be used with optional cable and lock kit.
  • Design includes screened air-vent to allow condensation and vapors to escape.
  • Elastic in the hem at front and rear helps hold the cover in place.
  • All seams are overlapped and double stitched for superior strength.
  • Includes screened air-vent to allow condensation and vapours to escape
  • Ready-Fit silver urethane covers carry a 1-year limited warranty to the original purchaser

Can I use the Ready Fit Motorbike Cover for Indoor and Outdoor Use?

Details : It is important to carefully select the cover suited to your vehicles storage conditions.  Ready Fit Motorbike Covers are available in a range of sttyles to suit most motorbikes, however there are other covers including Pack Lite and Form Fit of different qulity

How will the Ready Fit Motorbike Cover fit my Motor Cycle ?

The Ready Fit Motorbike covers have been designed for most popular bike configurations, you need to check the conigurations and model before ordering.  These are not a tailored perfect fit but do offer a better fit than a Standard universal fit Motorbike Cover

I have found a model that is very similar to my mtotorbike will this cover fit?

If you cannot find your motorbike listed then you need to find a cover based on your style of motorbike.  If you need assistance in choosing the correct cover for your Motorbike please contact us

Are the covers easy to put on?

The installation process and time that it takes depends on the size and shape of the motorbike you are covering, as with all covers installation does take a bit of time but in general all motorbike covers are relatively easy to install and remove.

What happens if I order the wrong Motorbike Cover?

In most cases you should be able to find your motorbike model listed if you cannot find your model listed then please contact or look at our fitting guide.

Is the Cover Easy to Clean?

Each different fabric type has different cleaning methods, please check this before placing your made to order motorbike cover order.

Do I need to use optional items such as Gust Guard and Clamp and Lock?

The Gust Guard is designed to help prevent the cover from lifting in windy conditions we reccomened using Gust Guard for long term storage usage and also the lock and cable for added cover security.  You would not generally require any extra fititngs for your Motorbike cover but if you frequently park in high wind conditions you might like to puchase the Gust Guard

Do you have a question that we have not answered ? Please detail your question below and we will come back to you soon.

Please describe your question so that we can assist you.
Please put this part number |SCOOTER-SIZE4| in the Part Number box below.

Installation

Installing your new cover is simple. To help with this, a "Front" tag is sewn on the inside of the cover so you can easily see which side is the front.  Once you’ve identified the front of the cover, secure this area of the cover around the front tire first, then pull the cover over the top of the handlebars and secure under the rear tire last.

You may wish to optionally reinforce the inside of your cover with duct tape for any areas that will be in direct contact with sharp places. This can help ensure that your cover will last as long as possible.

Removal

The following procedure will make it easier to remove and install the cover whenever it is used:

  • Release both ends of the cover from under the tires.
  • Fold up both sides onto the seat into a long pile.
  • Start at the front tire and fold the cover in one foot folds from the front to the back.

If you use the same procedure each time, you will find it only takes about 30 seconds to install or to remove the cover.

The elastic at each end of the cover will keep it in place under all normal conditions. Use care in installing the cover on a vehicle which has just been driven to be sure the material does not come in contact with hot exhaust pipes.

Cleaning Instructions

The generic cleaning instructions noted below are intended for use with all custom made Fabric covers but you should refer to the specific instruction sheet included with your purchase for any specific fabric care instructions.

Car Cover Performance ca be dramatically affected by dirt that builds up on and within the material.  It can cause the windshield and paint to become dirty and "fogged" as well as create "wicking" where is actually helps pull water through the fabric, nullifying the water resistant properties that the fabric originally may have had.  Cleaning your cover will help to keep your vehicle clean and will ensure that teh serviceable life of the cover is reached.

NEVER ... Clean a car cover in a washer

NEVER ... Use Fabric Softener

NEVER ... Dry a non-woven or speciality type cover in a dryer

(Weathershield® and Form-Fit® covers can be dried in a dryer with regular heat)

1)Using a large commercial washer without agitator, wash the cover using 1/4 cup of 303 Fabric Cleaner All Purpose Cleaner 9some weathershield covers are compact enough to be washed in a normal size washing machine).  Place the cover in the washer and pour the cleaner in the tub after its full with warm water or pour it directly into the machine (necessary for some wall mounted commercial units) then place the cover inside and start the machine.

2)Rinse the cover twice (2 x) to fully remove the cleaner

3)Air dry unless its a cover that is specifically noted that can be dried in a dryer with regular or low heat

A cover may also be cleaned by turning it inside-out on the vehicle

1)Mix 1 ounce 303 fabric cleaner all purpose cleaner per quart of warm water.

2)Spray or sponge onto the cover

3)Rinse with Plain Water (until no suds) and allow to air dry

 

Specific fabric Cleaning Instructions are below:


Care-Instructions-BLOCKIT-380.pdf
Care-instructions-DUSTOP.pdf
Care-Instructions-EVOLUTION.pdf
Care-instructions-FORMFIT.pdf

Please view our Standard Coverworld Terms before ordering.

Open Coverworld Terms Here


There is a lot of information on our Terms page, please read them and feel free to ask any questions, we have friendly sales staff ready to take your call or send us an email

Please view our Standard Warranty details before ordering.

Open Warranty Information Here