Ford Courier Single Cab Soft Tonneau Cover with existing Installed Buttons on Ute Tub

Soft Tonneau Ford Ranger XL Dual Cab | 2007 To Oct / 2011 for Utes with Buttons on Tub

tonno ute tarp

 

This Soft Tonneau is for utes that have existing buttons installed onto the ute tub, the Bunji loops are not fitted onto the cover so that you put them in the correct position to line up with your existing buttons. The Soft Tonno is supplied with a full fitting kit and you will need to install the buttons onto your ute tub. If you have previously had a soft tonneau then it is a special order item that does not have the bunjis attached so that you can line it up to your existing buttons CLICK HERE if you are installing a tonneau for the first time



Ford Ranger XL (PJ / PK) Dual Cab Ute | Replacement Soft Tonneau Cover

raner px xl soft ute tonneau cover buy online

Additional Information

Part # TONNEAU-STO-125-BLANK
Brand Coverworld
* Soft Tonneau Cover has a fully water proof lining on the top & the bottom of the Cover
* Unlike some other Tonneau Cover brands this Soft Tonneau will NOT Stretch or Shrink, also made with Rot Proof Bonded Thread
* Superior UV Resistance with the Tonneau Cover Material
* Replacement tonneau cover is a special order item please read description before buying this soft tonneau cover online
* 5 Year Warranty - Best quality Cover Made in Australia
Material Rip Stop Material
Shipping Normally Dispatched 1-2 Days
raner px xl soft ute tonneau cover buy online

Mouse over to zoom image

Details

Low price Shipping
Soft Tonneau Cover | Supplied with Fitting Inclusions
From Date : 2007 | End Date : Oct 2011
Product Detail : Bunji Loop Style Tonneau Cover
Compatible with Factory Headboard (Cabin Guard / Load rest) / Not for Sports Bars
Product Detail : Replacement Tonneau for vehicles with existing installed buttons

This Soft Tonneau Cover Designed for the Following Vehicle
Important Information about the Bunjis supplied with the Cover

Each tonneau cover has been designed to have bunjis installed at 25mm to 27mm up from the bottom edge of the cover. You may find that when you check the cover size that your already installed buttons are a bit lower down on the tub. If you need a different length bunji than the ones supplied please let us know when ordering. How to work out which size you need is below


The finished size of this cover is 1620mm length and 1646mm Width. The Cover is supplied with 75mm length bunjis loops. The Bunjis sit approximately 27mm up from the edge of the cover on the sides and the rear. Check your current installed Button positions otherwise the cover will be sent with the standard length of 75mm

If you require a different size you can choose 85mm (B170) 90mm (B180) 95mm (B190)


  • Manufacturer : Ford
  • Model : Ranger
  • Series : PX (PJ / PK)
  • Body : Dual Cab Ute
  • Fabric : Rip Stop PVC
  • Colour : Black
  • Blank Tonneau for Vehicles with Existing Buttons
  • Supplied with Fitting Components*
  • Includes Eyelet Durable Punch for Bunjis
  • 5 Year Warranty

 

BLANK SOFT TONNEAU COVERS

 

Blank Tonneau Covers are designed for this specific vehicle but the Bunji loops have not been attached to the cover so that you can fit them to line up with your existing buttons fitted to your ute tub. The included bunjis are the standard length bunji that line up to the same position as factory tonneau covers and many aftermarket covers. The bunjis will need to be installed on the cover which can be done with a centre punch or eyelet punch, you can optionally add an eyelet punch to your order


This tonneau cover has the following inclusions

  • 1 X Tonneau cover
  • 
  • 2 x Bar Brackets (300474)
  • 
  • 1 x Tonneau Support Bar
  •  24 x Rivets (300482)
  • 
  • 3 x Aluminium Rope Track-484mm long ea
  • 
  • 1 x Support Bar Sheath
  •  12 x Rope Buttons (300473)
  • 
  •  4 x Dowel

    • The Blank Tonneau Covers are a special order item and take 3-4 days to make


      This cover might not fit to existing hardware in your ute tub and may need to be removed prior to this cover fitment, this cover will not fit to existing press studs

I have already had a Soft Tonneau Cover fitted previously so can I use this Soft Tonneau Cover on my vehicle?

Yes : If you have already had a Tonneau Cover fitted then you will already have buttons on the side of the vehicle, so the Tonneau Cover we will supply is called a "Blank Tonneau" this means that the bunji loops will not be fixed to the Tonneau Cover when it is delivered you will need to install the bunji loops to line up with your existing buttons. A centre punch is required to install the Bunji loops onto blank Tonneau Covers.  The manufacturing time is up to 5 days for a "Blank Tonneau"  This is for Bunji Tonneaus

Blank Tonneau Covers are not supplied with a Tonno Lock

If you have previoulsy had a bunji style tonneau and have buttons drilled into your ute tub you can still fit a clip on tonneau cover but those buttons will not be required or used

Are there any reccomended procedures I should carry out to maximise the lifespan of my Soft Tonneau Cover ?

Yes:  The following procedures should be carried out for general Soft Tonneau Cover Maintenance :

1)Apply Bees Wax or Dri-Lube to Stitching at least twice per year, this will maintain the tonneau covers waterproofing ability and prevent stitching from degrading, a natural result of weather exposure.

2) For best cleaning results we reccomend that you use our Tonneau and Convertible Top Cleaning product, do not use any harsh chemicals or cleaning agents on the Tonneau Cover.

3)For extended lifespan 303 Aerospace Protectant offers advanced UV treatment and has been shown the extend life spans of PVC's and Vinyls exposed to the weather and UV

Do I need to use Support Bars?

Yes : The support bars reduce pressure on the Soft Tonneau under driving conditions, as they prevent flapping which can damage the UV lamination on the Tonneau Cover material.  Most Tonneau Cover are supplied with support bars, check the inclusions for this Tonneau, if support bars are not included and you dont currently have any then we reccomend purchasing them, your warranty could be voided if the cover it not properly used and installed.

Will the Tonneau Cover scratch the sides of my styleside Ute Body?

No : The Tonneau Cover has a soft felt lining runnning along the inside on your Tray edge and it will not scratch your vehicle

I have Sports Bars and / or Ladder Racks on my vehicle can you adjust the Soft Tonneau Cover to fit around them?

No : We do not do any custom modifications to our standard Tonneau Cover patterns, if you require special cut outs then you would need to take the Soft Tonneau Cover to a local Auto Trimmer and ask them to make these modifications for you.  Check this is possible before you place the order.

Do you Offer a Fitting Service?

No, all Tonneau Covers are supplied with esay to follow instructions which you can download before purchasing, typically an installation will take approximately one hour.

Do I need to buy any additional special tools or equipment?

All Fitting instructions detail any extra tools that are required for installation, check the instructions before purchasing, in most cases the standard fitting tools required are:

  • Rivet Gun
  • Drill
  • Marking Pen / Pencil
  • You will need to buy a small padlock to go through the Tonno Lock

I would prefer to use the Clip on No Body Drilling Soft Tonneau but sometimes the items in my ute extend a bit higher than the tray sides so will the Clip on Cover still fit?

Yes, Oversize loads are not a hassle with our stretch cord clip on system that hides out of sight under the cover until needed

I would prefer to use the Clip on No Body Drilling Soft Tonneau Cover but cant find one for my vehicle?

Clip On Soft Tonneau Covers are being introduced for most popular new vehicles as they are released.

What happens if I order the wrong Soft Tonneau Cover?

You should be able to find the exact Soft Tonneau Cover for your vehicle listed on our website, if you cannot see your model listed then please contact us before placing an order, as if your Tonneau Cover needs to be returned because of an ordeirng error then you will need to pay for the return freight costs and deducted from your refund will be a 10% restocking fee and your original delivery cost will not be refunded.  Note special order tonneas which include Blank tonneau covers custom tray covers cannot be returned due to order error.

Do you have a question that we have not answered ? Please detail your question below and we will come back to you soon.

Please describe your question so that we can assist you.
Please put this part number |TONNEAU-STO-125-BLANK| in the Part Number box below.

Fitting Instructions for Part Number 143SB

 

PX Ranger Space Cab Ute With Sports Bars : 11/2011 - To Current

 


 

For new Soft Tonneau Cover installations drilling of buttons will be required for the initial installation

 

You will need the following extra tools for cover installation

 

  • Rivet gun
  • Drill
  • 4.5mm Drill Bit
  • Measuring Tape
  • Silicon Sealant
  • Anti-corrosive primer

 

Contents

  • 1 x Tonneau Cover
  • 3 x Aluminium Rope Track
  • 2 x Bar Brackets
  • 1 x Tonneau Support Bar
  • 24 x Buttons
  • 28 x Rivets
  • 4 x Pieces of Dowell
  • 2 x Alum Sealing Angles

 

Please read the fitting instructions before ordering this Soft Tonneau Cover.  

 

Tonneau Part No. 143SB Fitting Instructions

Please view our Standard Coverworld Terms before ordering.

Open Coverworld Terms Here


There is a lot of information on our Terms page, please read them and feel free to ask any questions, we have friendly sales staff ready to take your call or send us an email

Please view our Standard Warranty details before ordering.

Open Warranty Information Here

* Required Fields

$199.00

Coverworld and the Coverworld website is not associated with Ford® and we use the Manufacturer and Model names to identify the aftermarket products that we supply to the Vehicle model.  Please contact your local Ford® dealer for branded Ford® products.