Ford Courier Single Cab Soft Tonneau Cover with existing Installed Buttons on Ute Tub

Important Information if you have previously had a Tonneau Cover Fitted

 

Our Tonneau covers come with Bunji loops installed onto the cover so that you only need to install the buttons onto the ute tub. In most cases your existing installed buttons will line up to the position of the bunji loops on the cover. So its important to check the buttons and button information before ordering. This Tonneau Cover has 20 attached bunjis, there are 6 at the back and 7 on each side positioned like the photo depicts, the Bunji size are size 180mm, which means 85mm drop on each side. If your existing buttons will not match up to this then you need to order a Blank Replacement Tonneau which will not have the bunji loops installed on the cover. But the Blank Tonneau Covers are made to order whereas the standard tonneaus are normally pre-made and ready to ship, so because they need to individually made to order the factory charge an extra manufacturing cost for the special order, so its best to get the standard tonneau cover if it fits with your existing installed buttons

 

Ford Courier Dual Cab Ute | Replacement Soft Tonneau Cover

Ford Courier Dual Cab Ute | Replacement Soft Tonneau Cover replacement cover

Additional Information

Part # TONNEAU-STO-120-BLANK
Brand Made for Coverworld
* Soft Tonneau Cover has a fully water proof lining on the top & the bottom of the Cover
* Unlike some other Tonneau Cover brands this Soft Tonneau will NOT Stretch or Shrink, also made with Rot Proof Bonded Thread
* Superior UV Resistance with the Tonneau Cover Material
* Australian made with super fast manufacturing turnaround time and Expedited delivery times
* 5 Year Warranty
Material Rip Stop Material
Shipping Made to Order usually dispatched within 5 days

* Required Fields

$204.00
Ford Courier Dual Cab Ute | Replacement Soft Tonneau Cover replacement cover

Mouse over to zoom image

Details

Replacement Tonneau Covers Do not have attached Bunji Loops fitted onto the Tonneau Cover
Ford Courier Dual Cab Soft Tonneu
From Date : 1999 | End Date : 2006
Suits Factory Headboard (cabin Guard / Load rest) - Not for Sports Bars
Product Detail : Replacement Tonneau for vehicles with existing installed buttons

This Soft Tonneau Cover Designed for the Following Vehicle

  • Ford
  • Courier
  • Dual Cab
  • 1999 to 2006

 

BLANK SOFT TONNEAU COVERS

 

If you have existing buttons installed onto your Ute tub then we provide a "Blank" Tonneau cover which means the Tonneau will be the correct size and shape for your specific vehicle but it will not have the bunji loops installed onto the Soft Tonneau cover

 

Each Soft Tonneau has a Standard Number of inclusions which are detailed on the instructions please read the instructions prior to order, they will also sent to you after you buy a soft tonneau cover to your email address

 


To Fit the Bunjis to your Tonneau cover to line them up to your existing buttons you will need to use a Centre Punch or Bunji Punch, you can optionally add a Bunji punch to your order

I have already had a Soft Tonneau Cover fitted previously so can I use this Soft Tonneau Cover on my vehicle?

Yes : If you have already had a Bunji style Tonneau Cover fitted then you will already have buttons on the side of the vehicle, so its important to check the buttons and bunji quantity and position before ordering.  In some infrequent cases the Tonneau Cover we will supply is called a "Blank Tonneau" this means that the bunji loops will not be fixed to the Tonneau Cover when it is delivered you will need to install the bunji loops to line up with your existing buttons. A centre punch is required to install the Bunji loops onto blank Tonneau Covers.  The manufacturing time is up to 5 days for a "Blank Tonneau"

 

If you have previoulsy had a Clip On Tonneau cover that you are replacing it will be necessary to remove your currently installed side rails and replace with the supplied rails and components with this kit

Blank Tonneau Covers are not supplied with a Tonno Lock.  They are also a special order item and cannot be returned due to change of mind or order error.

Are there any reccomended procedures I should carry out to maximise the lifespan of my Soft Tonneau Cover ?

Yes:  The following procedures should be carried out for general Soft Tonneau Cover Maintenance :

1)Apply Bees Wax or Dri-Lube to Stitching at least twice per year, this will maintain the tonneau covers waterproofing ability and prevent stitching from degrading, a natural result of weather exposure.

2) For best cleaning results we reccomend that you use our Tonneau and Convertible Top Cleaning product, do not use any harsh chemicals or cleaning agents on the Tonneau Cover.

3)For extended lifespan 303 Aerospace Protectant offers advanced UV treatment and has been shown the extend life spans of PVC's and Vinyls exposed to the weather and UV

Do I need to use Support Bars?

Yes : The support bars reduce pressure on the Soft Tonneau under driving conditions, as they prevent flapping which can damage the UV lamination on the Tonneau Cover material.  Most Tonneau Cover are supplied with support bars, check the inclusions for this Tonneau, if support bars are not included and you dont currently have any then we reccomend purchasing them, your warranty could be voided if the cover it not properly used and installed.

Will the Tonneau Cover scratch the sides of my styleside Ute Body?

No : The Tonneau Cover has a soft felt lining runnning along the inside on your Tray edge and it will not scratch your vehicle

I have Sports Bars and / or Ladder Racks on my vehicle can you adjust the Soft Tonneau Cover to fit around them?

No : We do not do any custom modifications to our standard Tonneau Cover patterns, if you require special cut outs then you would need to take the Soft Tonneau Cover to a local Auto Trimmer and ask them to make these modifications for you.  Check this is possible before you place the order.

Do you Offer a Fitting Service?

No, all Tonneau Covers are supplied with esay to follow instructions which you can download before purchasing, typically an installation will take approximately one hour.

Do I need to buy any additional special tools or equipment?

All Fitting instructions detail any extra tools that are required for installation, check the instructions before purchasing, in most cases the standard fitting tools required are:

  • Rivet Gun
  • Drill
  • Marking Pen / Pencil
  • You will need to buy a small padlock to go through the Tonno Lock

I would prefer to use the Clip on No Body Drilling Soft Tonneau but sometimes the items in my ute extend a bit higher than the tray sides so will the Clip on Cover still fit?

Yes, Oversize loads are not a hassle with our stretch cord clip on system that hides out of sight under the cover until needed

I would prefer to use the Clip on No Body Drilling Soft Tonneau Cover but cant find one for my vehicle?

Clip On Soft Tonneau Covers are being introduced for most popular new vehicles as they are released.

What happens if I order the wrong Soft Tonneau Cover?

You should be able to find the exact Soft Tonneau Cover for your vehicle listed on our website, if you cannot see your model listed then please contact us before placing an order, as if your Tonneau Cover needs to be returned because of an ordeirng error then you will need to pay for the return freight costs and deducted from your refund will be a 10% restocking fee and your original delivery cost will not be refunded.  Blank special order tonneau covers cannot be returned so please order a blank tonneau cover carefully.

Do you have a question that we have not answered ? Please detail your question below and we will come back to you soon.

Please describe your question so that we can assist you.
Please put this part number |TONNEAU-STO-120-BLANK| in the Part Number box below.

Fitting Instructions for Part Number STO-120

 

Ford Courier Dual Cab Ute : 1999 - 2006

Mazda Bravo Dual Cab Ute : 1999 - 2006

 


 

For new Soft Tonneau Cover installations drilling of buttons will be required for the initial installation

 

You will need the following extra tools for cover installation

 

  • Rivet gun
  • Drill
  • 4.5mm Drill Bit
  • Measuring Tape
  • Silicon Sealant
  • Anti-corrosive primer

 

Contents

    • 1 x Tonneau Cover
    • 3 x Aluminium Rope Track
    • 2 x Bar Brackets
    • 1 x Tonneau Support Bar
    • 12 x Buttons
    • 22 x Large Rivet
    • 4 x Pieces of Dowell
    • 1 x Tonneau Lock Kit Including 2 Large Rivets (not included in Blank Tonneau Kit)

 

Please read the fitting instructions before ordering this Soft Tonneau Cover.  

 

Download Fitting Instructions

Please view our Standard Coverworld Terms before ordering.

Open Coverworld Terms Here


There is a lot of information on our Terms page, please read them and feel free to ask any questions, we have friendly sales staff ready to take your call or send us an email

Please view our Standard Warranty details before ordering.

Open Warranty Information Here

Coverworld and the Coverworld website is not associated with Ford® and we use the Manufacturer and Model names to identify the aftermarket products that we supply to the Vehicle model.  Please contact your local Ford® dealer for branded Ford® products.